Qol tipli boru birləşməsinin yığılması
(1) Pre-installed the most important link of the pre-installation of the sleeve type pipe uyğunluq möhürün etibarlılığına birbaşa təsir göstərir. Xüsusi prekursorlar ümumiyyətlə tələb olunur.Armatur with small diameter can be pre-assembled on the bench vice. The specific approach is to use a uyğunluq matris kimi, qoz, sıxma qolu boruya sıxıla bilər. Əsasən borudan keçən qol tipləri varuyğunluq, qol tipli ucu birləşdirən başlıq, qol tipli üç yollu boru vasitəsilə uyğunluqvə digər növlər. Bu found that even for a batch of goods from the same manufacturer, the depth of the conical hole on theuyğunluq is often not the same, resulting in leakage, and this problem is often ignored. The correct way is to use what kind of uyğunluq is used at one end of the pipe, and the corresponding fitting tail is pre-installed with the same type of uyğunluq, so as to avoid leakage problems to the greatest extent. The end face of the pipe should be flush.
(2) After the pipe is sawed, it should be polished evenly on grinding wheel and other tools, and the burrs should be removed, cleaned and cleaned with high pressure air before use.
(3) Əvvəlcədən quraşdırma zamanı borunun koaksiallığı və uyğunluq should be kept as far as possible. If the pipe is too deviation, it will also cause sealing failure.
(4) The pre-installed force should not be too ambassador that the inner edge of the sleeve is just embedded in the outer wall of the pipe, and the sleeve should not be obvious deformation. When connecting pipes, assemble according to the specified tightening force. The clamping force of the 6-1 sleeve is 64-1 15N, 16ф MMR 259N, ф18mm for 450N. If the jacket deformation is serious in pre-installation, the sealing effect will be lost.
It is forbidden to add sealant and other fillers. Some people in order to achieve better sealing effect, in the card sleeve coated with sealant, the sealant was rushed into the hydraulic system, resulting in hydraulic components Yin nihole blockage and other faults.
(3) When connecting the pipe, the pipe should have enough deformation allowance to avoid the pipe being subjected to tensile force.
(four) When connecting the pipeline, it should avoid being subjected to lateral force, which will cause loose sealing if the lateral force is too large.
(five) when connecting the pipeline, it should be good once and avoid multiple disassembly, otherwise it will make the sealing performance worse.
Folding card sleeve type pipeuyğunluq quraşdırma
(1) 9-cu fəsildə tələb olunan boruların duzlanması əvvəlcə həyata keçirilməlidir;
(2) Boru mişar maşını və ya xüsusi boru kəsici maşın və digər alətlərlə tələb olunan uzunluğa uyğun olaraq kəsin, borunun əriməsinə (məsələn, alov kəsilməsi) və ya daşlama çarxının kəsilməsinə qətiyyən icazə verilmir; Boru ucunun içərisində və xaricində buruqları, metal çipləri və kirləri çıxarın; Pas əleyhinə agenti və borunun kirini çıxarınuyğunluq; Eyni zamanda borunun yuvarlaqlığını təmin etmək;
(3) qoz, qol boruya, qolun ön kənarı (kiçik ucu) borunun ağzından ən azı 3 mm, sonra isə boru boruya quraşdırılmışdır. uyğunluqt body cone hole, top until;
(4) Qayğı yavaş-yavaş sıxın, borunu hərəkət etməyənə qədər çevirin və sonra qayığı 2/3 - 4/3 dəfə sıxın;
(5) Açın və gödəkçənin boruya kəsilib-kəsilmədiyini və mövqeyin düzgün olub-olmadığını yoxlayın. Gödəkçənin eksenel hərəkətinə icazə verilmir, ancaq bir az fırlanma;
(6) Yoxlamadan keçdikdən sonra qozu sıxın.